NACE-CIP1-001 Questions - Truly Beneficial For Your NACE Exam (Updated 100 Questions)
View All NACE-CIP1-001 Actual Exam Questions, Answers and Explanations for Free
NEW QUESTION # 36
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Surface Temperature
- C. Low Relative Humidity
- D. High Surface Temperature
Answer: C
NEW QUESTION # 37
ISO SA 3 is directly equivalent to:
- A. NACE No. 3/SSPC SP 6
- B. None of the above
- C. NACE No. 1/SSPC SP 5
- D. NACE No. 2/SSPC SP 10
Answer: B
NEW QUESTION # 38
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Inorganic
- C. Resistant to concentrated sulfuric acid
- D. Organic
Answer: D
NEW QUESTION # 39
Polymerization is the process of:
- A. Monomers joining together
- B. Monomers telegraphing
- C. All thermoplastic coatings
- D. All organic coatings
Answer: A
NEW QUESTION # 40
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Call the supervisor
- B. Achieve consensus through negotiation
- C. Never change his/her mind
- D. Go with the majority opinion
Answer: A
NEW QUESTION # 41
Corrosion generally occurs at which of the following sites:
- A. Electrolyte
- B. Metallic pathway
- C. Cathode
- D. Anode
Answer: D
NEW QUESTION # 42
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Needle pressure gauge
- C. Profilometer
- D. Psychrometer
Answer: C
NEW QUESTION # 43
Solvents are added to coating formulations to
- A. increase film permeability.
- B. provide color.
- C. dissolve binders and form liquid coatings.
- D. decrease film permeability.
Answer: C
NEW QUESTION # 44
A magnetic pull-off type gauge is a good choice when:
- A. Accuracy is not required
- B. Performing an adhesion test
- C. When an intrinsically safe tool is required
- D. When working on non-ferrous metals
Answer: C
NEW QUESTION # 45
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION # 46
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Bring the matter up at the pre-job conference
- B. Default to the owner's Inspection and Test Plan
- C. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- D. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
Answer: A
NEW QUESTION # 47
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the job specification as a guide
- B. Call the coating manufacturer for clarification
- C. Use the product data sheet as a guide
- D. Call the person who wrote the specification for clarification
Answer: A
NEW QUESTION # 48
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. Organic solvents
- C. A wide variety of materials
- D. Biodegradable detergents
Answer: C
NEW QUESTION # 49
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. In the field only
- B. At all times
- C. Only if the specification requires it
- D. In the office only
Answer: B
NEW QUESTION # 50
An Inspector should change position when:
- A. The Inspectors position is not the majority position
- B. Only when directed by the supervisor
- C. The Owner can save some money by the change
- D. The Inspector is convinced by verifiable facts
Answer: D
NEW QUESTION # 51
Conventional spray is a good choice when:
- A. High transfer efficiency is required
- B. High viscosity coatings are being applied
- C. High production rates are required
- D. High quality finishes are required
Answer: D
NEW QUESTION # 52
The main responsibilities of the inspector are to
- A. observe and direct the work of the contractors.
- B. observe and report the quality of the work performed.
- C. demonstrate to the contractor how to apply the coating.
- D. direct and perform the work stated in the specification.
Answer: B
NEW QUESTION # 53
Galvanic corrosion occurs on which of the following substrates:
- A. Fiberglass Reinforced Plastic
- B. Metal
- C. Wood
- D. Concrete
Answer: B
NEW QUESTION # 54
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he cannot proceed
- B. Advise the Contractor he can proceed
- C. Advise the Contractor of your readings
- D. Call your supervisor
Answer: C
NEW QUESTION # 55
......
NACE-CIP1-001 dumps Free Test Engine Verified By It Certified Experts: https://www.exam-killer.com/NACE-CIP1-001-valid-questions.html
NACE-CIP1-001 Exam Free Practice Test with100% Accurate Answers: https://drive.google.com/open?id=1gK2LrEj_OJujDP7mEZm5Xery_TavAMAu
