Updated Aug-2023 200-301 Exam Practice Test Questions
Verified 200-301 dumps Q&As 100% Pass in First Attempt Guaranteed Updated Dump
Cisco 200-301 exam is a certification test for individuals seeking to become a Cisco Certified Network Associate (CCNA). Cisco Certified Network Associate Exam certification is recognized globally and is a valuable asset for IT professionals seeking to advance their career in networking. 200-301 exam covers a wide range of topics, including network fundamentals, network access, IP connectivity, IP services, security fundamentals, and automation and programmability.
NEW QUESTION # 204
Drag and drop the descriptions of file-transfer protocols from the left onto the correct protocols on the right.
Answer:
Explanation:
NEW QUESTION # 205
How will Link Aggregation be Implemented on a Cisco Wireless LAN Controller?
- A. When enabled, the WLC bandwidth drops to 500 Mbps.
- B. To pass client traffic, two or more ports must be configured.
- C. One functional physical port is needed to pass client traffic.
- D. The EthernetChannel must be configured in "mode active".
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration-guide/b_cg75/b_cg75_chapter_0100010.html
NEW QUESTION # 206
Drag the descriptions of IP protocol transmissions from the left onto the IP traffic types on the right.
Answer:
Explanation:
Explanation
TCP
* Sends tranmissions in sequence
4. Transmits packets individually
6. Uses a lower transmission rate to ensure relability
UDP
5. Uses a higher transmission rate to support latency-sensitive application
2. Transmissions include an 8-byte header
3. Transmits packets as a stream
NEW QUESTION # 207
Drag and drop the descriptions from the left onto the configuration-management technologies on the right.
Answer:
Explanation:
Explanation
Ansible:- uses SSH for remote device communication- uses YAML for fundamental configuration elements Chef:- uses TCP port 10002 for configuration push jobs- uses Ruby for fundamental configuration elements Puppet:- fundamental configuration elements are stored in a manifest- uses TCP 8140 for communication The focus of Ansible is to be streamlined and fast, and to require no node agent installation.Thus, Ansible performs all functions over SSH. Ansible is built on Python, in contrast to the Ruby foundation of Puppet and Chef.TCP port 10002 is the command port. It may be configured in the Chef Push Jobs configuration file .This port allows Chef Push Jobs clients to communicate with the Chef Push Jobs server.Puppet is an open-source configuration management solution, which is built with Ruby and offers custom Domain Specific Language (DSL) and Embedded Ruby (ERB) templates to create custom Puppet language files, offering a declarative-paradigm programming approach.A Puppet piece of code is called a manifest, and is a file with .pp extension.
NEW QUESTION # 208
What is the benefit of configuring PortFast on an interface?
- A. The frames entering the interface are marked with higher priority and then processed faster by a switch.
- B. After the cable is connected, the interface uses the fastest speed setting available for that cable type
- C. After the cable is connected, the interface is available faster to send and receive user data
- D. Real-time voice and video frames entering the interface are processed faster
Answer: C
NEW QUESTION # 209
Which output displays a JSON data representation?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: A
NEW QUESTION # 210
Which two statements about DNS lookup operations are true? (Choose two.)
- A. The client sends a request for IP address to domain name resolution to the DNS server.
- B. When the primary IP address of the destination is down, the DNS server can forward the client to an alternate IP address.
- C. The DNS server pings the destination to verify that is available.
- D. They use destination port 53.
- E. The client sends a request for domain name to IP address resolution to the DNS server.
Answer: D,E
NEW QUESTION # 211
An engineer must configure a/30 subnet between two routers. Which usable IP address and subnet mask combination meets this criteria?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION # 212
Refer to the exhibit. The network engineer is configuring a new WLAN and is told to use a setup password for authentication instead of the RADIUS servers.
Which additional set of tasks must the engineer perform to complete the configuration?
- A. Disable PMF Enable PSK Enable 802.1x
- B. Select WPA2 Policy Disable PMF Enable PSK
- C. Select WPA Policy Select WPA2 Policy Enable FT PSK
- D. Select WPA Policy Enable CCKM Enable PSK
Answer: B
NEW QUESTION # 213 
Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to
10.10.13.128/25 at Site A?
- A. It sends packets out of interface Fa0/2 only.
- B. It sends packets out of interface Fa0/1 only.
- C. It load-balances traffic out of Fa0/1 and Fa0/2.
- D. It cannot send packets to 10.10.13.128/25.
Answer: D
Explanation:
Section: IP Connectivity
Explanation:
Router2 does not have an entry for the subnet 10.10.13.128/25. It only has an entry for 10.10.13.0/25, which ranges from 10.10.13.0 to 10.10.13.127.
NEW QUESTION # 214
A Cisco engineer is configuring a factory-default router with these three passwords:
* The user EXEC password for console access is p4ssw0rd1
* The user EXEC password for Telnet access is s3cr3t2
* The password for privileged EXEC mode is pnv4t3p4ss Which command sequence must the engineer configured A)
B)
C)
D)
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: A
NEW QUESTION # 215
Drag and drop the DHCP snooping terms from the left onto the descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 216
Refer to the exhibit.
A packet is being sent across router R1 to host 172.163.3.14. To which destination does the router send the packet?
- A. 207.165.200.254 via Serial0/0/0
- B. 207.165.200.250 via Serial/0/0/0
- C. 207.165.200.246 via Serial0/1/0
- D. 207.165.200.254 via Serial0/0/1
Answer: B
NEW QUESTION # 217
Drag and drop the characteristics of network architectures from the left onto the type of architecture on the right.
Answer:
Explanation:
NEW QUESTION # 218
A network engineer is installing an IPv6-only capable device. The client has requested that the device IP address be reachable only from the internal network. Which type of IPv6 address must the engineer assign?
- A. link-local address
- B. IPv4-compatible IPv6 address
- C. aggregatable global address
- D. unique local address
Answer: D
NEW QUESTION # 219
......
To prepare for the Cisco 200-301 exam, candidates can take advantage of various resources, including Cisco’s official study materials, online courses, and practice exams. Candidates can also participate in study groups and online forums to discuss exam topics with other candidates and industry professionals. Hands-on experience with networking technologies and concepts is also a valuable asset when preparing for the exam.
Ultimate Guide to Prepare Free 200-301 Exam Questions and Answer: https://drive.google.com/open?id=1RVDSJIGCNcVHatXRElZEarzWjcIN6IGv
Pass CCNA 200-301 Exam With 875 Questions: https://www.exam-killer.com/200-301-valid-questions.html
