[Oct 10, 2023] Verified HPE6-A75 dumps and 72 unique questions
HPE6-A75 Dumps for Pass Guaranteed - Pass HPE6-A75 Exam 2023
NEW QUESTION # 16
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue.
The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. asymmetric routing introduced by a routing configuration error
- B. a hardware issue, such as a broken cable
- C. mismatched IP addresses on the VLAN for the link
- D. an issue with queuing, caused by mismatched QoS settings
Answer: B
NEW QUESTION # 17
Refer to the exhibit.
An AD user's department attribute is configured as *HR". The user connects on Monday using their Windows Laptop to a switch that belongs to the Device Group HQ.
Which role is assigned to the user in ClearPass?
- A. Remote Employee
- B. HR Local
- C. Executive
- D. iOS Device
- E. Vendor
Answer: A,B
NEW QUESTION # 18
in a VPN that uses certificate-based authentication, which component must be configured on the Mobility Master (MM) to allow a RAP to successfully connect to a Mobility Controller (MC)
- A. RAP IPSec pre-shared key
- B. RAP VPN username and password
- C. WLAN and new RAP group
- D. RAP whitelist
Answer: D
NEW QUESTION # 19
Refer to the exhibit.
Based on the configuration of me create_user form shown, which statement accurately describes the status?
- A. The visitor_phone field will be visible to the guest users in the web login page.
- B. The visitor_phone field will be visible to operators creating the account.
- C. The visitor_company field will be visible to the guest users when they access the web login page.
- D. The email field will be visible to guest users when they access the web login page.
- E. The visitor_company field will be visible to operators creating the account.
Answer: D
NEW QUESTION # 20
What is a typical reason to implement MAC authentication on an AOS-Switch?
- A. to filter traffic at the edge, based on multiple criteria in the MAC header
- B. to control management access to the switch CLI based on device, as well as user credentials
- C. to provision switch ports to support devices such as IP phones or printers
- D. to enhance the security of an 802.1X solution
Answer: D
NEW QUESTION # 21
Refer to the exhibit.
A company has attempted to implement OSPF without success. The devices in Area I need to be able to reach Area 2. Routes should be aggregated for advertisement in other areas. What must be changed to meet these requirements?
- A. Add the 10.2.0.0/16 range on Swttch-1 and the 10.1.0.0/16 range on Switch-2.
- B. Move the 10.1.0.0/16 range to Area 2 on Switch-1 and the 10.2.0.0/16rangetoArea 1 onSwitch-2.
- C. Add Area 1 and Area 2 on VIAN 100 on both Switch-1 and Switch-2. Remove Area 3.
- D. Change Area 3 to Area 0; remove Area 1 from Switch-2 and Area 2 from Switch-1.
Answer: D
NEW QUESTION # 22
Refer to the exhibit.
Traffic between the servers m Area l takes a less optimal path rather than the link associated with VLAN l OOO, subnet 10.0.0.0/30. Based on the exhibits, why is this the case?
- A. The link between Switch-1 and Switch-2 has gone down.
- B. The metric on the VLAN 1000 interface is too low.
- C. OSPF routing switches choose the best intra-area routes based on Area 1 links only.
- D. Switch-1 and Switch-2 cannot achieve adjacency on VLAN 1000 due to mismatches.
Answer: C
NEW QUESTION # 23
A company has a mixed wireless and wired Aruba solution. It wants to encrypt messages used to send configurations and other important messages to the APs carried outside the GRE tunnels.
What can the company do to meet these goals?
- A. Configure extended IP ACLs on the AOS-Switches to filter the traffic.
- B. Use PAPI enhanced security.
- C. Deploy Aruba Meridian and integrate the AOS-Switches with it.
- D. Use tunneled node to send traffic through an Aruba Mobility Controller.
Answer: D
NEW QUESTION # 24
Refer to the exhibit.
Based on the Attribute configuration shown, which statement accurately describes the status of attribute values?
- A. The attribute values of department, title, memberOf, telephoneNumber, and mail are directly applied as ClearPass.
- B. The attribute values of department and memberOf are directly applied as ClearPass roles.
- C. Only the attribute values of title, telephoneNumber, and mail can be used in role mapping policies.
- D. Only the attribute value of company can be used in role mapping policies, not the other attributes.
- E. Only the attribute values of department and memberOf can be used in role mapping policies.
Answer: B
NEW QUESTION # 25
A network administrator can set the OSPF metric-type on an AOS-Switch to Type 1 or Type 2. What is the difference?
- A. A Type 2 metric is assigned to multiple external routes that are aggregated together, while a Type 1 metric does not permit external route aggregation.
- B. A Type 2 metric stays the same as the external route is advertised, while a Type 1 metric increments with internal OSPF link costs.
- C. A Type 2 metric assigns cost 1 to a 100 Gbps link, while a Type 1 metric assigns cost 1 to all links of 100 Mbps or higher.
- D. A Type 2 metric marks external routes that can be advertised in NSSAs, while a Type 1 metric marks external routes that can only be advertised in normal areas.
Answer: B
NEW QUESTION # 26
An administrator configures the MultiZone feature for a company network, where a mobility cluster is the primary zone and a standalone controller in the company's DMZ represents a secondary data zone. The administrator configures two AP Groups and respective VAPs for the zones on the Mobility Master (MM) in the primary zone. When the APs boot up and establish connections to both zones, the administrator notices that no data connections are established to the data zone.
What must the administrator do to fix this problem?
- A. Have the MultiZone APs initially boot from the standalone controller in the data zone.
- B. Configure the same AP Group in the data zone as it is in the primary zone, and configure the VAPs in the data zone.
- C. Configure the same AP Groups and VAPs on the standalone controller, and associate the MultiZone APs to both groups.
- D. Create different AP groups and VAPs on the Mobility Master and standalone controllers, and associate the MultiZone APs to both groups.
Answer: D
NEW QUESTION # 27
Refer to the exhibit.
An employee connects a corporate laptop to the network and authenticates for the first time using EAP-TLS. Based on the Enforcement Policy configuration shown, which Enforcement Profile wilt be sent?
- A. Onboard Device Repository
- B. Onboard Post-Provisioning - Aruba
- C. Onboard Pre-Provisioning - Aruba
- D. Deny Access Profile
Answer: C
NEW QUESTION # 28
Refer to the exhibit.
Based on the configuration of me create_user form shown, which statement accurately describes the status?
- A. The visitor_phone field will be visible to the guest users in the web login page.
- B. The visitor_phone field will be visible to operators creating the account.
- C. The visitor_company field will be visible to the guest users when they access the web login page.
- D. The email field will be visible to guest users when they access the web login page.
- E. The visitor_company field will be visible to operators creating the account.
Answer: D
NEW QUESTION # 29
An AOS-Switch needs to implement tunneled node in role-based mode. Aruba ClearPass is configured to assign users for which the traffic should be tunneled to a role named tunnel. The Aruba Mobility Controller should apply policies associated with the employees group to these users.
What is the correct user role configuration on the AOS-Switch for this scenario?
- A. one user role named tunnel with employees set as the secondary role in the tunneled-node- command redirect
- B. two user roles, one named tunnel that uses the tunneled-node-redirect command, and one named employees
- C. one user role named employees with tunnel set as the secondary role in the tunneled-node- command redirect
- D. two user roles, one named employees that uses the tunneled-node-redirect command, and one named tunnel
Answer: C
NEW QUESTION # 30
Refer to the exhibit.
The network administrator needs to set up BGP between the two company switches. Switch-1 and Switch-2. The BGP connection does not establish. Based on the exhibits, what does the administrator need to do to fix the issue?
- A. Enter the network command for 10.0.0.0/24 in the router BGP mode on each switch.
- B. Enable the multihop option for the neighbor on each of the switches.
- C. Set the update source for the neighbor to the local loopback interface on each switch.
- D. Enable BGP on the interfaces that the switches use to reach each other.
Answer: C
NEW QUESTION # 31
Refer to the exhibit.
A company has attempted to implement OSPF without success. The devices in Area I need to be able to reach Area 2. Routes should be aggregated for advertisement in other areas. What must be changed to meet these requirements?
- A. Add the 10.2.0.0/16 range on Swttch-1 and the 10.1.0.0/16 range on Switch-2.
- B. Move the 10.1.0.0/16 range to Area 2 on Switch-1 and the 10.2.0.0/16rangetoArea 1 onSwitch-2.
- C. Add Area 1 and Area 2 on VIAN 100 on both Switch-1 and Switch-2. Remove Area 3.
- D. Change Area 3 to Area 0; remove Area 1 from Switch-2 and Area 2 from Switch-1.
Answer: D
NEW QUESTION # 32
Which technologies can prevent split brain in a VSF fabric that includes Aruba 2930F switches?
- A. VLAN MAD or ARP MAD
- B. OOBM MAD or LLDP MAD
- C. LLDP MAD or VLAN MAD
- D. ARP MAD or OOBM MAD
Answer: C
NEW QUESTION # 33
What must an OSPF router do when it receives a link state update?
- A. It must re-establish adjacency with its Designated Router and Backup DR.
- B. It must run the shortest path first algorithm.
- C. It must participate in a new election for the Designated Router and Backup DR.
- D. It must initiate a graceful restart timer.
Answer: B
NEW QUESTION # 34
Which situation requires an AOS-Switch interface to support MAC-based VLANs?
- A. The interface is configured to support Local MAC Authentication (LMA), authenticates endpoints against a non-default MAC group, and limits the address count to 1.
- B. The interface is configured to support 802.1X in user-based mode, connects to more than one endpoint at a time, and users are assigned to different dynamic VLANs.
- C. The interface has an extended MAC ACL applied to it in the inbound direction, and it has multiple tagged VLAN assignments.
- D. The interface has an extended MAC ACL applied to it in the outbound direction, and it uses VLAN ID as one of the criteria for rules.
Answer: C
NEW QUESTION # 35
An administrator implements the MultiZone feature and uses two clusters that utilize CPSec. A primary and a data zone are created. MultiZone APs successfully build sessions to the primary cluster but fail to establish sessions to the data zone cluster. What must the administrator do to solve this problem?
- A. Enable MultiZone booting in the MultiZone AP apboot configuration mode.
- B. Use different AP Group names for the two zones.
- C. Enable CPSec in the MultiZone profile for both the primary and data zone.
- D. Add the MultiZone APs to the data zone's CPSec whitelist.
Answer: B
NEW QUESTION # 36
......
Latest 100% Passing Guarantee - Brilliant HPE6-A75 Exam Questions PDF: https://www.exam-killer.com/HPE6-A75-valid-questions.html
HPE6-A75 Exam Dumps - Try Best HPE6-A75 Exam Questions: https://drive.google.com/open?id=15AqhqtHT7y7x0apyNEjnP8cosPoHzdte
