Instantly download 642-832日本語 updated real questions

Correct Answer: I  🗳️

Correct Answer:

Solution Steps need to follow as below:
When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4 Ipconfig ----Client will be receiving IP address 10.2.1.3
IP 10.2.1.3 will be able to ping from R4 , R3, R2, R1
Look for BGP Neighbourship Sh ip bgp summary ----- State of BGP will be in established state & will be able to receive I prefix
(209.65.200.241)
As per troubleshooting we are able to ping ip 10.2.1.3 from R1 & BGP is also receiving prefix of webserver & we are able to ping the same from R1. Further troubleshooting needs to be done on R1 on serial 0/0/1
Check for running config. i.e sh run for interface serial 0/0/1..

!

!
From above snapshot we are able to see that IP needs to be PAT to serial 0/0/1 to reach web server IP
(209.65.200.241). But in access-list of NAT IP allowed IP is 10.1.0.0/16 is allowed & need 10.2.0.0 /16 to
As per troubleshooting we are able to ping ip 10.2.1.3 from R1 & BGP is also receiving prefix of web server & we are able to ping the same from R1. Its should be checked further for running config of interface for stopping
Change required: On R1, In natting we need to add client IP address for reachability to server.
So in ticket Answer to the fault condition will be as below for

Correct Answer:

Solution Steps need to follow as below:
When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4 ipconfig ----Client will be getting 169.X.X.X
On ASW1 port Fa1/0/ 1 & Fa1/0/2 access port VLAN 10 was assigned but when we checked interface it was showing down Sh run ------- check for running config of int fa1/0/1 & fa1/0/2 (switchport access Vlan 10 will be there with switch
port security command). Now check as below
Sh int fa1/0/1 & sh int fa1/0/2

As seen on interface the port is in err-disable mode so need to clear port.
Change required: On ASW1, for port security need command to remove port-security under interface under interface fa1/0/1 & fa1/0/2.
So in ticket Answer to the fault condition will be as below for

Correct Answer:

Explanation:
EEM -> CLI based Management and Monitoring
SDM -> Provides a GUI for Administration
FTP -> Used for Backup and Restore
Cisco IOS Embedded Event Manager (EEM) is a powerful and flexible CLI based subsystem that provides
real-time network event detection and onboard automation. It gives you the ability to adapt the behavior of
your network devices to align with your business needs.
Cisco SDM is an intuitive, Web-based device-management tool for Cisco IOS@ Software-based routers.
The Cisco SDM simplifies router and security configuration through smart wizards, which help customers
and Cisco partners quickly and easily deploy, configure, and monitor a Cisco router without requiring
knowledge of the command-line interface (CLI). The Cisco SDM is supported on a wide range of Cisco
routers and Cisco IOS Software releases.
Cisco devices can use FTP to backup and restore configuration files and IOS software. Some examples of
this are shown below:
Example 1: Backing up manually
R1# copy startup-config ftp://kevin:[email protected] Address or name of remote host [ 192.168.22.33]?
Destination file name [r1-confg]?
Writing R1-confg !!!
3458 bytes copied in 3.443 secs (1243 bytes/sec)
Example 2: Backing up automatically
The configuration below will make a backup:
write-memory Trigger backup when running-config is copied to nvram time-period 1440 Trigger backup
every 1440 minuttes. 60*24=1440 !
ip ftp username kevin
ip ftp password dj7jS
!
archive
path ftp://192.168.2.33/R1-config
write-memory
time-period 1440Viewing
R1#show archive
The next archive file will be named ftp://192.168.2.33/R1-confg-4 Archive # Name
1 ftp://192.168.2.33/R1-confg-1
2 ftp://192.168.2.33/R1-confg-2
3 ftp://192.168.2.33/R1-confg-3 <- Most Recent

Correct Answer: A  🗳️